7588 NW 8th Street, Miami, Fl. 33126
Tel: 305-264-8391 Fax: 305-261-6637or 1-877-264-8391
DMX 3 - 8 Channel Controllers
User's Manual - Page 6
Digital Lighting Systems
OPTIMA-DS2/DS2-C Operating Instructions
III. Introduction
The OPTIMA-DS2 and DS2-C are
simplified versions of the OPTIMA-DS
controller. They have the same features
as the DS with the exception on the
master and individual dimming controls.
The DS2-C is the same as the Ds2 but is
locked on “chase only” by setting selector
S2 to 0. The FADE button on the DS2-C is
deactivated and does not perform any
Fig. 9 The OPTIMA-DS2 Front Panel
OPTIMA-DS2
4 channel logic DMX512
Fade/
Chase
Auto/
Man.
ALL
ON
ALL
OFF
Pattern
Speed
IV. Number of Channels
Configuration
The number of channels on both models
can be set to any value between 3 to 8
usaing rotary selector S1 on the back of
the unit. Refer to Fig. 8 to the right.
A - Dual Button Controls
V. The Control Panel - See figure 9 below.
1- PATTERN (Up-Down Buttons)
The “PATTERN” up-button increments the pattern number from 1 to 16. The “PATTERN” down-button performs the reverse
operation until number 1 is reached.
2- SPEED (Up-Down Buttons)
The “SPEED” up-button increments the chase speed from 1 to 255. The “SPEED” down-button performs the reverse operation
until it reaches a minimum of 1.
The LED’S above these buttons indicate the output status of the first four channels.
1 - FADE/CHASE SELECT
If the fade mode had been previously selected, depressing the Fade Select button
switches the OPTIMA-DS2 to the chase mode and vice-versa. The associated LED
turns on when the selected mode is fade. (Feature disabled on DS2-C version.)
2 - AUTO/MAN. SELECT
Selecting the AUTO/MAN. mode causes the OPTIMA-DS2 to automatically scroll
through all 16 chase patterns. Otherwise, the same pattern repeats unless changed
using the PATTERN up/down buttons. The associated LED is on when Auto is
selected.
3 - ALL ON SELECT
Selecting the ALL ON mode stops the chasing and fading cycles and causes all
channels to go into a static ALL ON mode. The associated LED is on when ALL ON
is selected.
4 - ALL OFF Select
All channels are blacked out and go to 0% intensity. When selected, the associated
LED turns on.
The following four buttons work as toggles. They turn the function on, if previously off, and turn it off, if previously on.
3
2
4
1
5
0
6
F
7
E
8
D
9
C
A
B
S1
S2
3
2
4
1
5
0
6
F
7
E
8
D
9
C
A
B
Selector S1
Number of Channels
Using a small tip
screw driver, rotate
the shaft and
position the arrow at
the desired number.
Valid range: from 3
to 8 Channels.
Fig. 8 OPTIMA - number of Channels and Chase/Fade Selection
Selector S2
Chase/Fade
OPTIMA-DS2 set to
“F”
(Chase and Fade)
OPTIMA-DS2-C set
to “0”
(Locked on Chase
Only)
B - Single Button Toggle Controls
OPTIMA-DS
OSUM
Rev. C 06/03
Copyright 2003 Digital Lighting Systems, All rights Reserved Specifications are subject to change without notice. Printed in U.S.A.
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern